Ferramentas do usuário

Ferramentas do site


phone:f1000

Diferenças

Aqui você vê as diferenças entre duas revisões dessa página.

Link para esta página de comparações

Ambos lados da revisão anteriorRevisão anterior
Próxima revisão
Revisão anterior
phone:f1000 [2016/10/21 22:27] facsiphone:f1000 [2022/11/07 11:31] (atual) – edição externa 127.0.0.1
Linha 1: Linha 1:
 ======UTStarcom F1000 / F1000G SIP Phone====== ======UTStarcom F1000 / F1000G SIP Phone======
-{{description>The F1000 is a SIP protocol wifi phone manufactured by UTStarcom in 2005. +=====Description=====
-It supports Wireless B on F1000 and wireless B/G on F1000G.}}+
  
 +The F1000 is a SIP protocol wifi phone manufactured by UTStarcom in 2005.
 +It supports Wireless B on F1000 and wireless B/G on F1000G.
 +
 +=====Agere T8307 Data Sheet=====
 +Processor
 +https://www.tripleoxygen.net/wiki/_media/phone/t8307_v0.2_datasheet.pdf
 +
 +LCD
 +https://www.tripleoxygen.net/wiki/_media/phone/gp-lcd-spec_kgm082b0_.pdf
  
 =====Serial Interface===== =====Serial Interface=====
Linha 10: Linha 18:
  
 It is possible to access it by two means. It is possible to access it by two means.
-====One==== 
-Open the device (which may crack the housing since it is difficult to open) 
-Check the board for TX, RX and GND test points. 
  
-====Two====+==== Recommended way ==== 
 The USB port at the bottom isn't a normal USB port. Its pinout configuration is: The USB port at the bottom isn't a normal USB port. Its pinout configuration is:
  
Linha 25: Linha 31:
 Note that it uses the additional unused 4th pin on the USB cable. Note that it uses the additional unused 4th pin on the USB cable.
  
 +==== Second way (not recommended) ====
  
 +Open the device (which may crack the housing since it is difficult to open). Check the board for TX, RX and GND test points.
  
  
Linha 45: Linha 53:
  
 On this step you want to search for the following text: On this step you want to search for the following text:
 +<code>
 httpInit: Upload RPM successfully initialized. httpInit: Upload RPM successfully initialized.
 httpInit: System File Registry successfully initialized. httpInit: System File Registry successfully initialized.
Linha 59: Linha 67:
 httpPwdConfAdd OK dXNlcjo4ODg4ODg= httpPwdConfAdd OK dXNlcjo4ODg4ODg=
 before taskSpawn sysPause before taskSpawn sysPause
 +</code>
 Take a closer look on this 2 lines: Take a closer look on this 2 lines:
 +
 httpPwdConfAdd OK YWRtaW46ODRKaTIzZGphVw== httpPwdConfAdd OK YWRtaW46ODRKaTIzZGphVw==
 +
 httpPwdConfAdd OK dXNlcjo4ODg4ODg= httpPwdConfAdd OK dXNlcjo4ODg4ODg=
  
Linha 72: Linha 82:
 You can change the admin password to anything you want by accessing the webpage. You can change the admin password to anything you want by accessing the webpage.
  
-Now follow meisted_sd tutorial and after flashing a 4.50 version, do a factory reset via web menu using admin account. (»Unlocking the UTStarCom F1000)+Now follow meisted_sd tutorial and after flashing a 4.50 version, do a factory reset via web menu using admin account.
  
 PS. I do not recommend the 4.50 version. I prefer flashing 3.80 because you cannot downgrade it or maybe cannot return to vonage's firmware by rewriting the vonages tftp link. PS. I do not recommend the 4.50 version. I prefer flashing 3.80 because you cannot downgrade it or maybe cannot return to vonage's firmware by rewriting the vonages tftp link.
 +
 +
 +===Meisted_sd flashing===
 +
 +Unlocking the UTStarCom F1000
 +This unlocking guide was made in a large part
 +from the unlocking guide 'rkworth' posted here:
 +»www.vonage-forum.com/fto ··· 464.html
 +I've added a few comments, which are [in brackets]
 +and then taken the extra step to totally remove
 +vonage from the phone. Here is his guide, and then
 +mine follows at the end.
 +
 +-------------------------
 +
 +
 +Password for firmware upgrade - utvonpw
 +
 +then-
 +
 +So I've managed to unlock the Vonage UT starcom F1000
 +wifi phone from Vonage. I think it's a first because
 +there's no other info on how to do this anywhere on the web.
 +
 +You'll need a Windows pc for this...
 +
 +The first thing to do is download the firmware from here:
 +
 +File name is F1000_V3.80st.exe
 +
 +just google for f1000 firmware.
 +
 +Run this self extracting archive - it's German but no need
 +to worry - just accept the defaults.
 +It should unpack 4 files.
 +
 +Next make sure your Vonage wifi phone is connected and registered
 +i.e. you can make a call. [Here, the phone never actually has to
 +connect to the internet. The password "utvonpw" is factory set
 +into the phone. You just need it connected on your wireless]
 +
 +Scroll through the menus on your phone and choose Wi-Fi
 +Settings / Network Parameters / Network Info.
 +
 +Take note of the IP address (you may not need this but it's
 +handy to have). Mine is 192.168.1.14.
 +
 +Exit out of the Network Info menu and go to the Misc menu
 +
 +Select Local TFTP Update.
 +At the Code prompt enter utvonpw
 +You'll see a message that says TFTP is a long process..
 +
 +Select Update
 +The Screen will say Connecting...
 +
 +Back to Windows PC and launch the fwupgrade.exe application
 +
 +After a split second you should see a phone list that shows the
 +IP address we had earlier.
 +
 +Click Update
 +
 +You'll get a warning not to turn off either the Computer, Phone
 +or Access Point...don't turn them off!
 +
 +Mine took about 45 seconds to push the firmware.
 +
 +The screen on the phone will read Processing...
 +
 +then Decompressing...
 +
 +Windows will say that the task was complete...you can close the
 +updater by clicking Cancel
 +
 +Phone is still Decompressing 3 minutes later...
 +
 +Then it will switch off.
 +
 +***DO NOT TURN IT BACK ON**** or your work will be undone by Vonage!
 +
 +-------THIS STEP IS REALLY IMPORTANT-------
 +
 +Disconnect your broadband. [You never actually had to have it connected]
 +
 +Don't power it off, just disconnect either the phone cable if DSL or
 +the Coax if on cable. It's important that your wireless network stays up.
 +
 +Check that you can no longer browse the internet on your windows pc.
 +
 +Turn the F1000 on and it will connect to your wireless network.
 +
 +It will try and register via your network but of course you are
 +disconnected so it can't - this is good!
 +
 +Go to the Misc menu on the phone and select remote TFTP server - it
 +should have a Vonage server address in here...change it to a single
 +letter "a" (Or any other setting to remove the vonage URL)
 +[This step isn't really needed if you keep the unit off a
 +wireless connection and complete my steps at the end of
 +this part. I've also been told this doesn't always work
 +to keep the unit from getting provisioned again if it
 +gets a wireless connection.]
 +
 +Turn the phone off
 +
 +Reconnect your broadband and ensure you CAN browse to a
 +webpage or two.
 +
 +Turn phone on and it will connect to your wireless network but
 +it will never Register as it can't find Vonage servers!
 +
 +Usng a web browser open the IP address that we remember from earlier.
 +(This actually connects you to the phones internal web server)
 +Login as user with password 888888 (six 8's)
 +
 +Click User Menu on the left and go immediately to SIP & RTP Config
 +
  
 =====Provisioning file===== =====Provisioning file=====
Linha 208: Linha 336:
 #Manually config SIP timer=T1T24000T45000TimerB32000TimerFTimerHTimerDTimerJ #Manually config SIP timer=T1T24000T45000TimerB32000TimerFTimerHTimerDTimerJ
 </code>  </code> 
 +
 +========
 +This software can create provisioning files for F1000
 +https://www.tripleoxygen.net/wiki/_media/phone/provisioning_1_1_42_x86.zip
 +From: https://sourceforge.net/projects/provisioning/
  
  
Linha 213: Linha 346:
  
 [[http://web.quick.cz/lake/f1000_faq.htm|UTStarcom F1000 FAQ]] [[http://web.quick.cz/lake/f1000_faq.htm|UTStarcom F1000 FAQ]]
 +[[https://www.dslreports.com/forum/r31016698-Definitive-Unlock-for-Vonage-F-1000-UTstarcom|DSL Reports Post]]
 +
 +==== Acknowledgments ====
 +
 +People involved in discussions, tips, or general chat. List in alphabetical order.
 +
 +facsi, Steve Hiddenvision, Tripleoxygen
 +
    
phone/f1000.1477088853.txt.gz · Última modificação: 2022/11/07 11:31 (edição externa)